修复你的物品 社区 商店

BlackBerry Storm LCD/Digitizer Replacement

简介

This guide will show you how to replace your broken or defective Digitizer & LCD assembly in your 9500/9530 Storm.

Before ordering your new part, check the number on your existing LCD, it will either be V.014 or V.024, shown in step 11.

你所需要的

  1. BlackBerry Storm LCD/Digitizer Replacement, LCD/Digitizer: 步骤 1 中的图像 1，1

    • Turn your Blackberry Storm 9500 onto its back side, and remove the battery door & battery.

    编辑

  2. BlackBerry Storm LCD/Digitizer Replacement: 步骤 2 中的图像 1，1

    • Remove the 2 screws (T6) under the battery compartment they are located as shown in red.

    编辑

  3. BlackBerry Storm LCD/Digitizer Replacement: 步骤 3 中的图像 1，1

    • Turn the Blackberry Storm 9500 around and pry off the microphone cover at the top using a safe pry tool.

    编辑

  4. BlackBerry Storm LCD/Digitizer Replacement: 步骤 4 中的图像 1，1

    • Remove the two screws(T6) as shown.

    编辑

  6. BlackBerry Storm LCD/Digitizer Replacement: 步骤 5 中的图像 1，1

    • Flip it back over to the back of the phone, and remove the plastic lens on top of the camera & flash. This is held in place by some adhesive, so use a safe pry tool to remove as shown.

    编辑

  7. BlackBerry Storm LCD/Digitizer Replacement: 步骤 6 中的图像 1，1

    • Once the plastic piece is removed, unscrew the two torx screws underneath it.

    编辑

  8. BlackBerry Storm LCD/Digitizer Replacement: 步骤 7 中的图像 1，3 BlackBerry Storm LCD/Digitizer Replacement: 步骤 7 中的图像 2，3 BlackBerry Storm LCD/Digitizer Replacement: 步骤 7 中的图像 3，3

    • Now use a safe pry tool, and go along the edges of the phone to release the clips to open the housing. There are a total of 6 clips, 3 on each side.

    • There is a small cap connection that connects the antenna to the logic board as pictured.

    编辑

  9. BlackBerry Storm LCD/Digitizer Replacement: 步骤 8 中的图像 1，1

    • Once you have worked you way all the way around the device with the safe pry tool you can now separate the two pieces of the housing.

    • *Be sure to remove the antenna cable in the top portion of the housing. You will need to reattach this when you repair the phone*

    编辑

  10. BlackBerry Storm LCD/Digitizer Replacement: 步骤 9 中的图像 1，1

    • Now remove the logic board & LCD assembly from the rear housing. Be gentle, and do not use excessive force.

    编辑

  11. BlackBerry Storm LCD/Digitizer Replacement: 步骤 10 中的图像 1，2 BlackBerry Storm LCD/Digitizer Replacement: 步骤 10 中的图像 2，2

    • Flip the logicboard around so that it is sitting on top of the screen, now remove the two ribbon cables for the LCD & Digitizer.

    编辑

  12. BlackBerry Storm LCD/Digitizer Replacement: 步骤 11 中的图像 1，1

    • Put your broken assembly to the side, and now install your new one following the past steps in reverse.

    • Before ordering your new part, check the number on your existing LCD, it will either be V.014 or V.024. (Shown in blue)

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

13等其他人完成本指南。

作者

与2其他贡献者

Josh Forester

于11/28/10注册

2,497 声望

创作了10篇指南

徽章: 31

+ 28更多徽章

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 5

总计 21,096