简介

Use this guide to replace the motherboard on your RIM BlackBerry 7290.

With your index finger, press down on the lock button to unlock the battery cover. Slide the battery cover down towards you to reveal the battery. Slide the battery cover down towards you to reveal the battery.
  • With your index finger, press down on the lock button to unlock the battery cover.

  • Slide the battery cover down towards you to reveal the battery.

添加评论

Use your index finger to lift and remove the battery from the phone. Use your index finger to lift and remove the battery from the phone. Use your index finger to lift and remove the battery from the phone.
  • Use your index finger to lift and remove the battery from the phone.

添加评论

Slide the SIM card holder to the left to unlock the SIM card.
  • Slide the SIM card holder to the left to unlock the SIM card.

添加评论

Lift the SIM card holder up. Gently remove the SIM card from the SIM card holder.
  • Lift the SIM card holder up.

  • Gently remove the SIM card from the SIM card holder.

添加评论

Remove the four top screws using a T-6 torx screwdriver.
  • Remove the four top screws using a T-6 torx screwdriver.

  • The top four screws are .413 inches.

添加评论

Remove the two bottom screws using a T-6 torx screwdriver. The bottom two screws are .2 inches in length.
  • Remove the two bottom screws using a T-6 torx screwdriver.

  • The bottom two screws are .2 inches in length.

  • The second picture displays the device after the six screws have been removed.

添加评论

Use the plastic opening tool to apply pressure on the two clips that are located at the bottom of the phone.
  • Use the plastic opening tool to apply pressure on the two clips that are located at the bottom of the phone.

添加评论

With both of the bottom clips unhooked, lift the bottom portion of the phone and slide it upwards (towards your fingers) to detach the back cover from the front cover. With both of the bottom clips unhooked, lift the bottom portion of the phone and slide it upwards (towards your fingers) to detach the back cover from the front cover. With both of the bottom clips unhooked, lift the bottom portion of the phone and slide it upwards (towards your fingers) to detach the back cover from the front cover.
  • With both of the bottom clips unhooked, lift the bottom portion of the phone and slide it upwards (towards your fingers) to detach the back cover from the front cover.

添加评论

Using a T-6 screwdriver, remove the screw located on top of the phone. After the screw has been removed, carefully lift the side button brace to reveal the side button.
  • Using a T-6 screwdriver, remove the screw located on top of the phone.

  • After the screw has been removed, carefully lift the side button brace to reveal the side button.

添加评论

To remove the logic board mounting plate, start by loosening one side of the phone.
  • To remove the logic board mounting plate, start by loosening one side of the phone.

添加评论

With one side loosened, simply lift the logic board mounting plate off of the phone's front cover.
  • With one side loosened, simply lift the logic board mounting plate off of the phone's front cover.

添加评论

Turn the logic board mounting plate over to reveal the LCD display.
  • Turn the logic board mounting plate over to reveal the LCD display.

添加评论

Peel off the rubber keypad buttons from the face plate. Peel off the rubber keypad buttons from the face plate.
  • Peel off the rubber keypad buttons from the face plate.

添加评论

Use a plastic opening tool to unhook the LCD display from the logic board mounting plate.
  • Use a plastic opening tool to unhook the LCD display from the logic board mounting plate.

添加评论

With the clip unhooked, gently pull off the LCD display from the phone. With the clip unhooked, gently pull off the LCD display from the phone.
  • With the clip unhooked, gently pull off the LCD display from the phone.

添加评论

Remove the the three screws that are highlighted in red using a T6 torx screwdriver. The screw is .2 inches in length.
  • Remove the the three screws that are highlighted in red using a T6 torx screwdriver.

  • The screw is .2 inches in length.

添加评论

Remove the screw using a T6 torx screwdriver
  • Remove the screw using a T6 torx screwdriver

  • The screw is .2 inches in length.

添加评论

Separate the logic board mounting plate from the logic board. Separate the logic board mounting plate from the logic board.
  • Separate the logic board mounting plate from the logic board.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

kmathew

于2009年10月17日注册

3 信誉积分

创作了5篇指南

团队

Cal Poly, Team 19-6, Maness Fall 2009 Cal Poly, Team 19-6, Maness Fall 2009 的会员

CPSU-MANESS-F09S19G6

5 名成员

创作了7篇指南

hi wonder if you can help or give me advice on my device. its not turning on looks like it turns on with the hour glass turning but nothing happens

douwmg - 回复

my device doesn't want to switch on its just the hour glass on the screen that turns on the screen but its not turning on?

douwmg - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 4,696