跳转到主内容

修复你的物品

维修的权力

商店

简介

使用本指南更换 Apple Watch Series 3 中的Force Touch垫圈。本指南介绍了连接显示屏时的步骤。如果你希望断开显示屏或更换显示屏,请参阅 本指南 并在取下显示屏后更换Force Touch 垫圈。这将使垫圈定位更容易一些。

  1. 准备iOpener,并加热显示屏以软化粘合剂,将其固定到位。
    • 准备iOpener,并加热显示屏以软化粘合剂,将其固定到位。

    I have heated up the iOpener to 165 degrees and left it on for more than a minute. No way I can lift the screen off with the exact knife. Tried different angles in various places, but no go. I also used a hair dryer un til the watch screen was too hot to touch and even tried a very hard cutting tool blade and also no go. Could n ever get the blade under the face I applied enough force where I could see that the blade left small marks, not very big, but could never get anything to move or lift. What am I doing wrong? I spent 47 years at a global computer company and I am used to taking apart small things and applying force when required. I don’t know what I am doing wrong. Please help me.

    Rafael Blanco - 回复

    Getting the initial gap is not easy. Maybe a playing card could work its way in the tiny gap and cut some adhesive. After that there might be some success with an exacto knife. Or you want to try a piece of aluminum foil (folded for more rigidity) for cutting the adhesive. Be aware of the force touch gasket and that it might get damaged during that procedure.

    Tobias Isakeit -

  2. 始终保持手指完全远离刀。 千万不要施加太大的压力,因为这可能会导致刀滑动并切割或损坏手表。 仅将刀片的细边插入间隙,然后朝您的方向倾斜刀片以加宽间隙,并将显示屏略微抬起。 将弯曲刀片的边缘放入显示器和外壳之间的薄间隙中。 从显示屏的短边开始,最靠近圆形圈。
    • 始终保持手指完全远离刀。 千万不要施加太大的压力,因为这可能会导致刀滑动并切割或损坏手表。

    • 仅将刀片的细边插入间隙,然后朝您的方向倾斜刀片以加宽间隙,并将显示屏略微抬起。

    • 将弯曲刀片的边缘放入显示器和外壳之间的薄间隙中。 从显示屏的短边开始,最靠近圆形圈。

    • 不要将刀插入1/16英寸(约2毫米)。

  3. 一旦使用刀片打开了小间隙,请移除刀片并将打开工具的较薄边缘插入间隙中。 在此插入翻译将开口工具推入间隙,用拇指作为支点,将显示屏再打开一点。
    • 一旦使用刀片打开了小间隙,请移除刀片并将打开工具的较薄边缘插入间隙中。

    • 在此插入翻译将开口工具推入间隙,用拇指作为支点,将显示屏再打开一点。

    • 现在不要试图完全分离显示屏。 Force Touch垫圈可能会粘在显示器或机身上,如果用力过猛,可能会被撕裂。

  4. 在显示屏下方插入一个开口拨片,小心地将Force Touch垫圈与显示屏分开。 确保您找对了位置。 如果在抬起显示屏时把Force Touch垫片分离了,或者您将垫圈层分开,则还需要更换Force Touch垫圈本身。 在显示屏周围滑动拨片以分离Force Touch垫圈和显示屏之间的粘合剂。
    • 在显示屏下方插入一个开口拨片,小心地将Force Touch垫圈与显示屏分开。

    • 确保您找对了位置。 如果在抬起显示屏时把Force Touch垫片分离了,或者您将垫圈层分开,则还需要更换Force Touch垫圈本身。

    • 在显示屏周围滑动拨片以分离Force Touch垫圈和显示屏之间的粘合剂。

    • 不要将开口拨片插入深度超过1/16英寸(~2 mm)。

  5. 为避免损坏显示屏电缆,请勿完全打开显示屏。 将显示屏打开约45°角,然后用镊子剥去显示屏和Force Touch垫圈之间的粘合剂。 将粘合剂穿过显示器电缆的周围和后面,使其完全脱落,然后向下按压垫圈以重新粘附到盒子上。
    • 为避免损坏显示屏电缆,请勿完全打开显示屏。

    • 将显示屏打开约45°角,然后用镊子剥去显示屏和Force Touch垫圈之间的粘合剂。

    • 将粘合剂穿过显示器电缆的周围和后面,使其完全脱落,然后向下按压垫圈以重新粘附到盒子上。

    • 如果Force Touch垫圈本身松动且不会向下弯曲,则应更换垫圈下方和垫圈与显示屏之间的粘合剂。

  6. 卸下固定金属盖板的Y型#000螺丝。 用一把镊子取下盖板。 首先打开盖板。
    • 卸下固定金属盖板的Y型#000螺丝。

    • 用一把镊子取下盖板。

    • 首先打开盖板。

    • 然后将其关闭一半,将其完全取出。

    Pictures are the GPS version. Cellular doesn’t have the gap and separate removable plate on the “taptic engine” section.

    Ryan Holt - 回复

    What if I’m unable to unscrew the screw? I’m using the right tool, but it just won’t do it. It feels like it can’t “lock in” if you know what I mean in order to be able to get enough grip to turn the screw. Any suggestions?

    Cade Capper - 回复

  7. 在仅有GPS的版本上,可以在卸下金属板后立即断开电池。 对于LTE版本,你首先需要断开Force Touch垫圈并将其折叠,以便断开电池连接。 使用撬棒的尖端直接向上撬起连接器来断开电池连接。 稍微弯曲连接器,确保它不会意外接触到主板。
    • 在仅有GPS的版本上,可以在卸下金属板后立即断开电池。 对于LTE版本,你首先需要断开Force Touch垫圈并将其折叠,以便断开电池连接。

    • 使用撬棒的尖端直接向上撬起连接器来断开电池连接。

    • 稍微弯曲连接器,确保它不会意外接触到主板。

  8. 使用撬棒的尖端通过从外边缘直接向上撬动力触摸垫圈来断开它。 使用撬棒的尖端通过从外边缘直接向上撬动力触摸垫圈来断开它。
    • 使用撬棒的尖端通过从外边缘直接向上撬动力触摸垫圈来断开它。

  9. 准备一个iOpener,并将其放在 Force Touch 垫圈的顶部,以软化下面的粘合剂。
    • 准备一个iOpener,并将其放在 Force Touch 垫圈的顶部,以软化下面的粘合剂。

    • 小心显示屏电缆,不要拉出得太多。

  10. 用一把镊子剥掉 Force Touch 垫圈。 稍微向前倾斜显示屏并沿对角方向握住 Force Touch 垫圈,将其穿过显示器并将其取下。
    • 用一把镊子剥掉 Force Touch 垫圈。

    • 稍微向前倾斜显示屏并沿对角方向握住 Force Touch 垫圈,将其穿过显示器并将其取下。

    Does the metal connector for the gasket “clip” in place? Any tips on how to do that?

    Stephen Magladry Magladry - 回复

  11. 在棉签上涂抹一点异丙醇(> 90%酒精)或使用清洁垫轻轻去除Force Touch垫圈上残留的任何粘合剂。 要取下显示屏电缆下方的粘合剂,请将显示屏几乎关闭,并在清洁时轻轻将其拉离边缘。
    • 在棉签上涂抹一点异丙醇(> 90%酒精)或使用清洁垫轻轻去除Force Touch垫圈上残留的任何粘合剂。

    • 要取下显示屏电缆下方的粘合剂,请将显示屏几乎关闭,并在清洁时轻轻将其拉离边缘。

    I recommend removing the screen, getting the new Display Connectors Sticker Set (IF334-009-1 for my 38mm version), and cleaning the housing. Made it much easier to clean and apply the touch force gasket.

    Ryan Holt - 回复

    Which job has the sticker which connects the display flex with the housing? These stickers can‘t found on the series 2 but on the series 3? I damaged one of the two connections when I cleaned the old glue. I‘ve tested 3 force touch cable stickers and none worked…is there any connection? Help

    chrkraemer - 回复

  12. 翻转手表,使显示屏平放,同时略微抬起外壳。 小心地从显示器背面取下任何残留的粘合剂。
    • 翻转手表,使显示屏平放,同时略微抬起外壳。

    • 小心地从显示器背面取下任何残留的粘合剂。

  13. 使用一把镊子小心地从新的Force Touch垫圈底部取下保护膜。 使用一把镊子小心地从新的Force Touch垫圈底部取下保护膜。
    • 使用一把镊子小心地从新的Force Touch垫圈底部取下保护膜。

    My force touch sensor looks different than this one. It says it’s a 38/2/3Cell on the package but it has a different connection than the one in the pictures.

    Jonathan McGahey - 回复

  14. 沿对角方向握住 Force Touch 垫圈,将其穿过显示屏。 稍微向前倾斜显示屏,以便将Force Touch垫圈与框架对齐。 从 Force Touch 垫圈连接器对面的角落开始,将垫圈放在框架上,然后向下按压。
    • 沿对角方向握住 Force Touch 垫圈,将其穿过显示屏。

    • 稍微向前倾斜显示屏,以便将Force Touch垫圈与框架对齐。

    • 从 Force Touch 垫圈连接器对面的角落开始,将垫圈放在框架上,然后向下按压。

    • 你可以使用撬棒的末端将新的 Force Touch 垫圈按压到位。

  15. 通过撬棒轻轻按下柔性电缆重新连接。 通过撬棒轻轻按下柔性电缆重新连接。
    • 通过撬棒轻轻按下柔性电缆重新连接。

    Any tips to seating these connectors? How positive (tight) are the connections.

    Stephen Magladry Magladry - 回复

  16. 使用镊子将覆盖电池接口的金属板放回原位。 安装Y型#000螺丝。
    • 使用镊子将覆盖电池接口的金属板放回原位。

    • 安装Y型#000螺丝。

    • 此时,你可能需要打开手表并检查一切是否正常,然后再将其关闭。

  17. 使用一把镊子轻轻取下 Force Touch 垫圈顶部的保护膜。 使用一把镊子轻轻取下 Force Touch 垫圈顶部的保护膜。 使用一把镊子轻轻取下 Force Touch 垫圈顶部的保护膜。
    • 使用一把镊子轻轻取下 Force Touch 垫圈顶部的保护膜。

  18. 对齐显示屏并将其牢牢按在粘合剂上。
    • 对齐显示屏并将其牢牢按在粘合剂上。

    • 为了进一步改善粘合剂的粘合程度,你可以使用iOpener预热显示器,然后再将其按下约一分钟。

终点

40等其他人完成本指南。

特别感谢这些译者︰

en zh

17%

Yuting Zhao正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Dominik Schnabelrauch

于2016年11月23日注册

88,988 信誉积分

创作了375篇指南

团队

iFixit iFixit 的会员

Community

134 名成员

创作了15,657篇指南

very detailed teardown. however seems like the force touch sensor is a bit different on the LTE version.

The LTE parts actually looks similar to the Series 2 ones. Does anyone know if S2 and S3 force touch sensor is compatible to each other?

George - 回复

After replacing the screen and the force touch sensor everything except the force touch works.

I have tested 4 force touch sensor flex…what can it be?

chrkraemer - 回复

Hello I’ve got the same problem. Have you resolved it ?

Perhaps it’s necessary to reinstall watchOS ?

In my case applewatch is locked, to many error code access. And I don’t have iphone brother with me….so I can’t reset applewatch.

Frederic Berger - 回复

Reinstalling watchOS is impossible. Only Apple can do it…

my only problem is still the non-working force touch.

chrkraemer -

Same problem, replaced battery while broke the force touch gasket. After replaced a new gasket, the force touch still not working.

Patrick -

Warning! Inserting the screw to the plate that holds down the battery connector and the GPS antenna was very difficult. I actually lost the screw and thought it was down inside the watch. I removed the battery to see if it shake out. I realized that it was not inside the watch. My last hope was looking on the area rug with a big magnifying glass. Low and behold I found it. Tip! Do not try this repair on a bare wooden tabletop. That tiny little screw will bounce a long way if you drop it. You need to work on a soft rubber mat or on the top of the magnetic parts mat that Fixit sells. After several attempts trying to get that screw started, I still failed. Eventually, I had to use the tweezers from Fixit to hold the screw then dab a tiny bit of Gorilla glue on the Y0000 bit and hold the screw with the pliers and push onto the bit until it dries. Once the screw was glued to the bit I had no problem.

Albert Holler - 回复

Same here, repaired the display and used a new touch sensor, force touch is still not working… any suggestions?

Frank H. - 回复

Did everything but now my touch sensor isn’t working at all …. Heellllppp me?

Junior Tulloch - 回复

Do not buy the repair kit for the apple watch. I bought the repair kit for a broken screen, an new battery and an extra force touch sensor just to play it safe. The adhesive on the force touch sensor does not work. Even after following the instructions of placing a weight (book) on it for several hours the adhesive doesn’t hold. Save your money and buy a new watch.

Robert Gammariello - 回复

Same issue here. My screen separated from the case on its own, guessing I wore it too much! Anyways, I ordered the force touch gasket and when it didn’t work the first time ifixit did send me a new one as it didn’t seem to have adhesive on one side…new one seems to also have this issue. Just save yourself time and a small headache and get a new one.

Andrew Horvath -

For all those with the force touch problem- This may have been caused by damaging the internal force touch ring, located in-between the digitizer/glass layer and the OLED display. Impossible to fix. However, in watchOS 7, Apple removed the force touch feature and replaced it with Haptic Touch, which is basically de-glorified force touch. Just tap and hold gently on the display and it will be triggered, with no need for the force touch ring.

Braden Lambiase - 回复

En el series 3 LTE + GPS, si no se pone eso que le pasa al Apple Watch?

elchidote_chubby - 回复

添加评论

浏览统计数据:

过去的24小时: 39

过去的7天: 194

过去的30天: 882

总计 20,942