简介

As a computer is used, it generates heat. The cooling fan pulls air through the device to cool it down. If it becomes clogged with dust or breaks, the computer will overheat.

配件

无需配件。

Place the laptop on a flat surface with the bottom side facing up.
  • Place the laptop on a flat surface with the bottom side facing up.

  • Place the tip of a spudger or finger into the hole on the battery release slider.

添加评论

Use the spudger to move the slider to the right and hold it there.
  • Use the spudger to move the slider to the right and hold it there.

  • With the slider held, use your other hand to pull the battery back away from the laptop.

添加评论

  • This step will void your device warranty.

  • Use the screwdriver to pierce the warranty sticker.

  • Unscrew and remove the #0 6mm Phillips screw and set it aside.

Bradley,

If I replace the chrome os Hard drive with one that has a Linux distro already installed will the linux work normally or is there something built in to stop it.

It's something I do with an old dell I use for checking out distros.

Regards,

Jack

jack martin - 回复

I guess it's too late to answer this question now, but C710 is not IBM PC-compatible so standard linux distros do not run normally on it without any modifications.

You can flash a IBM PC-compatible bootloader(coreboot+SEABIOS) on it to run other linux distros.

cdac1234 -

Any suggested source for getting the 4 Gb RAM upgrade? Does this RAM have a model number?

rwells78 -

What is the hard drive called, or it's specific name, so that I may search around for a replacement, before taking my laptop apart?

Jennifer Munoz - 回复

Mine is a Seagate ST320L T020

Marshall Gates -

do not so what the second picture shows and leave the battery in!

brayton1234567 - 回复

  • Slide the back panel towards you. The best spots to place your fingers are on the bumpers.

  • Lift on the front edge to remove the panel.

添加评论

  • The hard drive assembly is attached to the laptop by a ribbon cable. Only lift the side of the drive facing you about an inch above the laptop. If you tear the ribbon cable the laptop will need to be serviced by a professional.

  • Use one finger to lift up the hard drive assembly from the bottom left corner.

添加评论

  • Hold the hard drive assembly keeping the end closest to you near the laptop. It's ok to tilt the far end of the drive up towards you.

  • Unscrew the two silver #0 3mm Phillips screws on the left and right sides of the hard drive.

添加评论

  • Hold the base of the hard drive in your right hand.

  • Use your left hand to pull the hard drive away from its housing. Don't let the housing tug on the ribbon cable.

添加评论

  • Pull the metal tabs sideways away from the memory stick.

  • The RAM stick will pop up.

添加评论

  • Pull the RAM stick up and away from the laptop.

添加评论

  • Use a spudger or your fingernails to lift up and unclip the two gold connectors on the top of the wireless card.

添加评论

  • Unscrew the black #0 3mm Phillips screw at the top right of the wireless card.

添加评论

  • The wireless card will spring up.

  • Pull the wireless card up and out to remove it.

添加评论

  • Remove the SD card or placeholder by pressing the card in until it clicks and pops out.

  • Pull the card out.

  • Remove the screws.

    • Sixteen #0 6mm Phillips screws

    • One #0 3mm screw

添加评论

  • Unplug the fan power cable by pulling the cable towards you using a spudger to help pop off the connection.

添加评论

  • Unplug the cable below the lower RAM slot by using the spudger to slide the two brown clips towards you.

  • Gently pull the cable towards you using the clear plastic tab.

添加评论

  • Unclip the bottom half of the case from the laptop by using a spudger and starting at the USB port on the right side of the laptop. Then work your way clockwise around the laptop.

添加评论

  • Open the laptop hinge about 45 degrees.

  • Lowering the keyboard assembly too far will damage the keyboard ribbon cable. Do not let the cable stretch.

  • Lower the keyboard assembly halfway between the case and the screen.

添加评论

  • Push down on the black tabs with a spudger to free the ribbon cable from the case.

  • Gently pull the ribbon cable out of its slot.

添加评论

  • Lower the keyboard assembly towards the screen until the clips near the hinges detach.

  • Set the keyboard assembly aside.

添加评论

  • Open the hinge to about 90 degrees.

  • Lift up the left edge of the tape holding the fan on the right side of the motherboard.

  • Push the fan out of the back of the laptop.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

4等其他人完成本指南。

Bradley Pavy

于2013年09月30日注册

1,083 信誉积分

创作了6篇指南

团队

Cal Poly, Team 13-3, Forte Fall 2013 Cal Poly, Team 13-3, Forte Fall 2013 的会员

CPSU-FORTE-F13S13G3

5 名成员

创作了7篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 9

过去的30天: 26

总计 5,476