修复你的物品 社区 商店

3DR Solo Leg Replacement

简介

This guide shows how to remove the legs on the bottom of the drone.

你所需要的

  1. 3DR Solo Leg Replacement, Propeller: 步骤 1 中的图像 1，1

    • Grip the arm, which is located underneath the propeller, with one hand, and with your dominant hand grip the center of the propeller.

    编辑

  2. 3DR Solo Leg Replacement: 步骤 2 中的图像 1，1

    • Twist the propeller from the locked to unlocked position as indicated by the images of the lock.

    • You will need to twist in this direction for 2-3 full rotations before the propeller will detach.

    编辑

  3. 3DR Solo Leg Replacement: 步骤 3 中的图像 1，1

    • Lift the propeller off the motor.

    • To remove the silver-top propellers, repeat these steps, turning the propellers in the opposite direction of the black-top propellers.

    编辑

  4. 3DR Solo Leg Replacement, Leg: 步骤 4 中的图像 1，1

    • Place the controller on a flat surface with the battery side down.

    编辑

  6. 3DR Solo Leg Replacement: 步骤 5 中的图像 1，3 3DR Solo Leg Replacement: 步骤 5 中的图像 2，3 3DR Solo Leg Replacement: 步骤 5 中的图像 3，3

    • Locate the leg and remove the two 10mm screws that hold the leg in place.

    编辑

  7. 3DR Solo Leg Replacement: 步骤 6 中的图像 1，1

    • Gently pull the leg up to remove it from its position.

    • Leg should be connected by a black wire.

    编辑

  8. 3DR Solo Leg Replacement: 步骤 7 中的图像 1，3 3DR Solo Leg Replacement: 步骤 7 中的图像 2，3 3DR Solo Leg Replacement: 步骤 7 中的图像 3，3

    • Locate the rubber grip at the end of the leg and, with your thumb, peel it back and pull it off.

    编辑

  9. 3DR Solo Leg Replacement: 步骤 8 中的图像 1，2 3DR Solo Leg Replacement: 步骤 8 中的图像 2，2

    • Leg type 1 will contain a 1mm screw at the base of the leg.

    • Unscrew the 1mm screw located at the end of the leg.

    编辑

  10. 3DR Solo Leg Replacement: 步骤 9 中的图像 1，1

    • Gently pull the black cord up to release it from the leg.

    编辑

  11. 3DR Solo Leg Replacement: 步骤 10 中的图像 1，3 3DR Solo Leg Replacement: 步骤 10 中的图像 2，3 3DR Solo Leg Replacement: 步骤 10 中的图像 3，3

    • Leg type 2 will contain the antenna wire.

    • Gently pull up on and remove the plastic covering labeled "solo antenna".

    • Locate the antenna wire and carefully pull up and remove it.

    • The antenna wire is flimsy so use caution upon removal.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与3其他贡献者

Leia Harlow

于09/11/17注册

101 声望

撰写一个指南

徽章: 4

+1个徽章

团队

CSU Fullerton, Team S2-G3, Bruce Fall 2017 CSU Fullerton, Team S2-G3, Bruce Fall 2017 的会员

CSUF-BRUCE-F17S2G3

4 名成员

创作了5篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 1

过去 30 天： 3

总计 322