跳转到主内容

简介

The 1999-2004 Jeep Grand Cherokee has a common failure where the blower fan wire adapter overheats and melts. Use this guide to fix and repair this connector and get your AC and Heater working again!

  1. Place the car in park, activate the parking break, and leave the car running. The blower motor is located under the dash on the passenger side of the vehicle. Push the seat back, and place your tools on the floor of the car. The blower motor is located under the dash on the passenger side of the vehicle. Push the seat back, and place your tools on the floor of the car.
    • Place the car in park, activate the parking break, and leave the car running.

    • The blower motor is located under the dash on the passenger side of the vehicle. Push the seat back, and place your tools on the floor of the car.

  2. There are a few wires hanging below the passenger side dash. The blower motor adapter is a bundle of three wires located on the left side.
    • There are a few wires hanging below the passenger side dash.

    • The blower motor adapter is a bundle of three wires located on the left side.

    • While the car is on push and pull gently on the wire connection.

    • If the fan turns on you have identified the problem and we will fix it.

    • If the fan does not turn on the damage may not be fixable without purchasing new parts.

    • Do not grasp any wires you can not see. Do not grasp any wires that are not covered in insulation and or electrical tape.

  3. Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物

    Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物
  4. Turn off the car. There are two screws holding the adapter in place. Using a philips screw driver, remove both screws and the adapter will come down. The two screws are identical. Be careful not to lose them.
    • Turn off the car.

    • There are two screws holding the adapter in place. Using a philips screw driver, remove both screws and the adapter will come down.

    • The two screws are identical. Be careful not to lose them.

    • Be sure the car is completely off before unscrewing anything.

  5. The connection between the three wires and the adapter box is the location of the common melting default. Observe the damage and decide if electrical tape will be enough to hold the wires in place.
    • The connection between the three wires and the adapter box is the location of the common melting default.

    • Observe the damage and decide if electrical tape will be enough to hold the wires in place.

    • Replacement parts are available for purchase if the damage is beyond repair.

  6. Using electrical tape wrap the wires tightly until there are securely in place.
    • Using electrical tape wrap the wires tightly until there are securely in place.

  7. Screw the adapter back into place. Turn on the car and test the AC/Heater Turn on the car and test the AC/Heater
    • Screw the adapter back into place.

    • Turn on the car and test the AC/Heater

结论

Enjoy your working AC and Heater!

6等其他人完成本指南。

William Schaller

于2015年02月24日注册

347 信誉积分

撰写一个指南

团队

Cal Poly, Team 24-1, Green Winter 2015 Cal Poly, Team 24-1, Green Winter 2015 的会员

CPSU-GREEN-W15S24G1

4 名成员

创作了3篇指南

radical, thank you for this!

cgerdes714 - 回复

Very good job - thanks for the info

I own one WJ 4.0 m1999

The ac doesn’t turn on(no lights)

Is this loose wire connection responsible for this?

ANGELO - 回复

good job thanks

rad8253 - 回复

添加评论

浏览统计数据:

过去的24小时: 11

过去的7天: 84

过去的30天: 493

总计 22,712