修复你的物品 社区 商店

联想笔记本电脑的维修和支持指南。

2554 个问题 查看全部

更多选项

Lenovo Legion Y530 Black screen after RAM upgrade and repaste

I’ve repasted my Lenovo Legion Y530, and also upgraded the RAM. I was stupid and forgot to disconnect the battery before the process.

However the laptop worked fine for an hour after reassembly, but then the screen suddenly went dark. (the connected external monitor is dark as well)

The device still starts up (windows welcome sound), the fans are spinning, keyboard lights are on, but the screen remains black

I’ve tried battery removal and discharging, and also tried to enter the BIOS but all i got was 12 short beeps followed by 1 separate beep. I’ve checked the Lenovo Beep Codes, but couldn’t find an exact match for this pattern.

Did I just kill my laptop? Is there any hope for getting it back up without motherboard replacement (which is not an option)?

Lenovo Beep Codes: https://support.lenovo.com/us/en/solutio...

回答此问题 我也有这个问题

这是一个好问题吗？

是 否
得分 1
添加一条评论

3个答案

筛选条件:
最有帮助的 最新 最老的
最有帮助的答案

更多选项

Hi @folt,

My first thought (as it worked for an hour) is that something wasn't quite put back where it needed to be and has wiggled loose. Have you tried opening it back up and double checking that you everything unplugged in your repair was re-connected firmly and clamped back into place?

这个答案有帮助吗？

是 否
得分 2
添加一条评论

更多选项

Hi @folt,

To add to Amber’s answer - Have you tried Fn+F6 to increase display brightness or Fn+F7 to toggle between the laptop display and an external display or with the computer off press the Novo button (little hole near side USB 3.1 port) using a paper clip (something without sharp tip) to start the BIOS setup utility? Lenovo Legion Y530 Hardware Maintenance Manual may help: https://usermanual.wiki/Lenovo/legiony53...

I tend to agree with Amber that something, especially LCD cable connector, was not connected securely or correctly. Moving the lid would certainly loosen it.

这个答案有帮助吗？

是 否
得分 2
添加一条评论

更多选项

Usually, unless you do a display service the backlight fuse survives. Now yes, never do that again but I wouldn’t be surprised if the fuse is fine. I’ve made this mistake with RAM and SSDs before, and I was fine.

Your best bet is to disconnect both the primary and CMOS batteries for 1-2 minutes, hold the power button for 30 seconds and reconnect it to reset the BIOS settings back to default and see if that helps.

这个答案有帮助吗？

是 否
得分 1

1条评论:

Update! I tried (re)connecting everything as You guys adviced. Everything was OK.

On Windows 10 I had no success but after booting the laptop with an other SSD (Linux) an external monitor became fully functional. The laptop screen displayed a VERY dimmed unreadable screen but it was the Ubuntu desktop.

What I tried/noticed:

* When I switched the main display to the external monitor (to conveniently access desktop), the external monitor became very dimmed as well, and UI elements did't respond to clicks.

* After it switching back, it was good again but the laptop remained black in both setting.

What I also tried, with no effect:

* Disconnect the battery

* Clear CMOS

* Discharge the device by holding the power button for 30s+

What I can’t do:

* Access BIOS, I get the same beep codes as described in the original post. Even if I could, the screen brightness is not enought to seen&navigate.

Can a motherboard/gpu/cpu(?) be "Partially Dead" with such limited functionality (with no realistic hope of repair)?

由完成的

添加一条评论

添加你的答案

Folt 将永远感激不已
浏览统计数据:

过去 24 小时： 1

过去 7 天： 1

过去 30 天： 10

总计 889