QWERTYUIO not working-I know there are some post re this BUT none work

Question

2012年中 MacBook Pro 13" 一体化机

发布于 2012 年 6 月, 型号 A1278. Intel 处理器，支持 Turbo Boost, 最多 512 MB DDR5 显存

1624 个问题查看全部

John @donjuanelguapo

声誉积分: 1

1

发帖于: 2020年5月19日

更多选项

QWERTYUIO not working-I know there are some post re this BUT none work

I just switched out my dead logic board on my Macbook Pro 13” mid 2012.

Everything seems to be working but some keys in the keyboard are not. Specifically, QWERTYUIO [ ] = and the power button. Oddly enough P works fine.

I have tried everything I found here. I can’t reset PRAM or SMC because both require buttons on the keypad that aren’t working. Are there other solutions that aren’t already listed here on ifixit?

By the way, the keyboard was working fine before the logic board died. I don’t think it’s the logic board based on everything I’ve read here. I know there is a solution but, for the life of me, I can’t find one. Please help.

Thanks,

John

Two more photos:

Edited: Here is a photo of the ribbon. I’m pretty sure it’s connected correctly.

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 0

添加一条评论

1个答案

已选择的解决方案

lemerise @lemerise

声誉积分: 37.6千

315

66

72

发帖于: 2020年5月19日

更多选项

Is an external USB keyboard works ? Check if the keyboard ribbon cable is well inserted into the connector, also look carefully at the connector and the cable end. Also verify the keyboard connector area for missing or damaged capacitors or resistors or corrosion in the area. Good luck :-)

这个答案有帮助吗？

是否

得分 3

6条评论:

I'm going to try an external keyboard. I did check the ribbon. I don't see any damage but it possibly could be damaged with all the attempts I made to plug it in correctly. I finally used the tape method to insert it properly. I don't see any corrosion or damage. I did clean the area with compressed air and also isopropyl. No dice on either one of those. This seems to be a common problem with MBPs and makes me wonder if I'm missing some easy fix or not doing it right.

由 John 完成的 2020年5月19日

@donjuanelguapo - The issue is getting the connection secured properly to the logic board. I've seen cables not inserted fully, damaged cables as well as damaged logic board connector. Yes, getting the cable in is a bit tricky!

Post some pics so we can see things: 在已经存在的问题里加入图片

由 Dan 完成的 2020年5月19日

@danj Photo added to original post.

由 John 完成的 2020年5月19日

@donjuanelguapo - Can you take a second one with the latch up so I can see the solder joints under it.

由 Dan 完成的 2020年5月20日

@danj Photos added to original post. Sorry by phone doesn't take clearer pics.

由 John 完成的 2020年5月20日

显示更多的1条评论

添加一条评论

I'm going to try an external keyboard. I did check the ribbon. I don't see any damage but it possibly could be damaged with all the attempts I made to plug it in correctly. I finally used the tape method to insert it properly. I don't see any corrosion or damage. I did clean the area with compressed air and also isopropyl. No dice on either one of those. This seems to be a common problem with MBPs and makes me wonder if I'm missing some easy fix or not doing it right. — John
@donjuanelguapo - The issue is getting the connection secured properly to the logic board. I've seen cables not inserted fully, damaged cables as well as damaged logic board connector. Yes, getting the cable in is a bit tricky!

Post some pics so we can see things: 在已经存在的问题里加入图片 — Dan
@donjuanelguapo - Can you take a second one with the latch up so I can see the solder joints under it. — Dan
@danj Photos added to original post. Sorry by phone doesn't take clearer pics. — John

2012年中 MacBook Pro 13" 一体化机

QWERTYUIO not working-I know there are some post re this BUT none work

1个答案

添加你的答案