shut down iPhone with black screen

Question

iPhone 3G

iPhone 3G是第二代iPhone。型号A1241，有8或16 GB容量，和炫酷的黑色或洁白的白色塑料背面。修复比第一款iPhone更简单。需要螺丝刀、撬撬工具和吸尘工具。

1158 个问题查看全部

dublincore @dublincore

声誉积分: 11

1

发帖于: 2011年5月30日

更多选项

shut down iPhone with black screen

After battery replacement, iphone 3g's screen is black. Phone itself works, it rings on incoming calls and texts. For all I've been reading here it probably has to do with the connectors.

Question is: how do I shut the phone down with a non-working display? I do not want to re-plug those connectors with voltage on. $^!@ non-removable battery! Any hints greatly appreciated!

All attempts to switch it off by doing the typical gesture failed. I know this because it's tethered and the Mac gives me status. So touch digitizer also seems to be off, too.

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 0

添加一条评论

2个答案

已选择的解决方案

Brad @brad80191

声誉积分: 24.4千

35

16

30

发帖于: 2011年5月30日

更多选项

See if your Mute/Vibrate switch works, if so you can use it to verify iPhone is OFF. Connected to Computer, or iTunes or the program you are using, so you can tell when the iPhone shuts OFF. Hold at same time Home and Power buttons for about 3-5 seconds till iPhone goes OFF, then release the buttons. To be certain check with Mute/Vibrate switch.

这个答案有帮助吗？

是否

得分 2

2条评论:

Hi Brad, thanks for your speedy reply.

The steps you mention above don't work for me. Device remains ON. But good to know anyway, that this 5-sec-home-power do a shutdown (on proper hardware).

Maybe the connection which brings the home button to logic board is the same as for the graphics which doesn't work? Does anyone know the assignment of what function go over what ribbon/connection?

Is there a (Mac-)software that powers down the device?

Thanks a lot!

由 dublincore 完成的 2011年5月31日

I love you! My screen is unresponsive and I wasn't looking forward to a long wait for my 3G to go flat. Holding the home and power buttons just until the slide instruction disappears from the screen is perfect. Thank you for showing me this!

由 T W 完成的 2017年8月27日

添加一条评论

Hi Brad, thanks for your speedy reply.

The steps you mention above don't work for me. Device remains ON. But good to know anyway, that this 5-sec-home-power do a shutdown (on proper hardware).

Maybe the connection which brings the home button to logic board is the same as for the graphics which doesn't work? Does anyone know the assignment of what function go over what ribbon/connection?

Is there a (Mac-)software that powers down the device?

Thanks a lot! — dublincore
I love you! My screen is unresponsive and I wasn't looking forward to a long wait for my 3G to go flat. Holding the home and power buttons just until the slide instruction disappears from the screen is perfect. Thank you for showing me this! — T W

dublincore @dublincore 声誉积分: 11 1 · Answer 1 · 2011-05-31T06:11:49-07:00

dublincore @dublincore

声誉积分: 11

1

发帖于: 2011年5月31日

更多选项

Hi Brad and others,

finally, I managed to fix it. Shutdown now works as expected and as described. Problem was that the home button wasn't able to work properly due to a contact loss right underneath itself. The two contact clips weren't able to reach the mating surfaces. After fixing that, the device shut down after 5 sec. button press and the way was clear to inspect the connections that caused the display to stay dark. Thanks again!

这个答案有帮助吗？

是否

得分 0

添加一条评论

iPhone 3G

shut down iPhone with black screen

2个答案

添加你的答案