Samsung LED TV model UA40C6900VMXZK, Not turning ON,

Question

Samsung Television

Repair guides and support for your Samsung TV.

2610 个问题查看全部

Satendra g @satendrag

声誉积分: 23

2

发帖于: 2018年9月11日

更多选项

Samsung LED TV model UA40C6900VMXZK, Not turning ON,

Hi guys,

My samsung LED TV not turning ON, I can hear continuous clicking sound from power relay (on Power board), whenever i unplug main board from power board, clicking sound disappear, but still no light visible even from hole of backside,

NOTE- Not observed any type of over heating, bulged cap, getting stand by voltage 5V.

Power Board model - PD46AF1E_ ZSM BN44 00357A

main board model - CN09BN9500411AL003ZCG0024 (LTF400HJO5 - LTJ400HJ05-A)

Checked voltage from main board to power board, it's dropping

Prompt reply will be highly appreciated,

Regards

Satendra from INDIA

回答此问题我也有这个问题

这是一个好问题吗？

是否

得分 1

1条评论

thanks for reply, but still same problem

由 Satendra g 完成的 2018年9月11日

添加一条评论

2个答案

oldturkey03 @oldturkey03 声誉积分: 782.2千 1.1千 893 2.3千 · Answer 1 · 2018-09-11T17:48:32-07:00

最有帮助的答案

oldturkey03 @oldturkey03

声誉积分: 782.2千

1.1千

893

2.3千

发帖于: 2018年9月11日

更多选项

Satendra g disconnect the cable going from the main board to the power board. Then turn your TV on. Let us know if your backlight comes on.

TROUBLESHOOTING

No Power

SYMPTOM

The LEDs on the front panel do not work when connecting the power cord.The SMPS relay does not work when connecting the power cord.

The units appears to be dead.

CHECK POINTS

The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning. In this case, check the following:Check the internal cable connection status inside the unit.

Check the fuses of each part.

Check the output voltage of SMPS.

Replace the Main Board.

Check ‘Main power input’ ? - BD1026 : B18VS_PW - BD1020: B13V - BD1023 : B5V

Check Output of ‘Stand-By Power IC’ ? - Pin#3 of IC4 : A3.3V > Change the Main Assy.

Check Input power of ‘T-con b’d’ - F1(T-CON) : B13V > Reconnect or Change the LVDS cable.

Check Power of ‘T-con b’d’. - L9(T-CON) : VCC12 - TP_VCC33 : VCC33 > Change the T-con B’d.

If nothing else you want to consider posting some images of all of your boards. that will allow us to see what you see. use this guide 在已经存在的问题里加入图片 for that

这个答案有帮助吗？

是否

得分 3

10条评论:

hii, oldturkey, i disconnected cable which come from main board no light visibile at all. ??????. i attached pic of power and main board for further action. thanks

由 Satendra g 完成的 2018年9月11日

You backlight gets the power from the power board after receiving the enable backlight signal from the main board. When you disconnect the mainboard from the power board, your backlight should come on. Since this is not happening, it is most likely that the issue is your power board. Check the fuses on your power board for continuity.

由 oldturkey03 完成的 2018年9月12日

But checked voltage from main board back to power board, it's dropping. Like 5 v then 12 V again 5V

由 Satendra g 完成的 2018年9月12日

Satendra g where are you checking the voltage and nder waht condition. TV on/off etc.

由 oldturkey03 完成的 2018年9月12日

I m checking in ON condition, On T- board, however after removing cable of main board clicking sound disappeared, but backlight still didn't ON

由 Satendra g 完成的 2018年9月14日

显示更多的5条评论

添加一条评论

Jesus @robertulrich 声誉积分: 1 · Answer 2 · 2018-09-11T22:54:50-07:00

Jesus @robertulrich

声誉积分: 1

发帖于: 2018年9月11日

更多选项

The power board is broken ,I think you can have a look this

https://www.abctay.com/vizio-dps200pp190...

这个答案有帮助吗？

是否

得分 0

1条评论:

hii jesus, how can u say that, power board is fine and getting 5 V from main board, power relay continuously clicking. Thanks for reply. awaitig some more info from you.

由 Satendra g 完成的 2018年9月11日

添加一条评论

Samsung Television

Samsung LED TV model UA40C6900VMXZK, Not turning ON,

2个答案

添加你的答案