PS4 CUH-1216D no power after Power Supply Swap

Question

PlayStation 4

索尼的新一代电视游戏机，于2013年2月20日发布，并于2013年11月15日开售。

1695 个问题查看全部

Róbert Fekete @robsferic

声誉积分: 103

4

5

发帖于: 2018年6月3日

更多选项

PS4 CUH-1216D no power after Power Supply Swap

Hi so a few days ago I asked here how to fix the PS4 that won't turn on, you guys were super helpful and told me that the easiest way was to replace the PSU and so I did. I ordered one from a place that offers 2 years of warranty and it came in this Wednesday. I had prepared the PS4 so I would only have to connect the new PSU and test it. So I plugged everything in and drum roll....nothing. So I hope you can help me decide my next step. I would really like to fix my PS4.

I tried multiple power cords.

I tried changing the HDD.

It turns out that the ps4 got high tension and a chip was busted on the motherboard. I imagine it was during a storm.

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 1

2条评论

You're 100% sure it's plugged in fully with a good power cord?

由 TronicsFix 完成的 2018年6月4日

Hi there! Yes I tried with my working ps4's cord and with my ps3 's cord none of them worked. No power at all not with eject button not with power button and also tried to put a Blu ray in to se if that activates the console but nothing.

由 Róbert Fekete 完成的 2018年6月4日

添加一条评论

1个答案

已选择的解决方案

Scott @scott35006

声誉积分: 10千

15

29

4

发帖于: 2018年6月5日

更多选项

not powering on can be far too many things to just instantly diagnose.

before going any further, run a diagnostic on your PSU.

https://www.youtube.com/watch?v=RG6x1B52...

If you dont have a Multimeter to run the above test, i would suggest either getting one, and learning to use it, or looking to a professional to do your electronics repairs.

If you get the proper voltage output in your PSU after the above tests, then your PSU is fine. At this point, plug it in to the board, and check that it is making a connection to the board at the point of the 5V leads. The 5V connector is what powers the LEDs and the buttons.

anything further than this, is likely a board level failure, and you will need to either run full board diagnosis (many hours of labour), or replace the logic board. If you replace the logic board in the PS4, you will also need to replace the PCB in the optical drive, as serials ar married.

i hope this helps.

这个答案有帮助吗？

是否

得分 1

7条评论:

My PSU is an ADP-200ER (4 pin) not a ADP-240AR like the one in the video.

由 Róbert Fekete 完成的 2018年6月5日

then you should get the same reading, only it will begin a slow discharged immediately.

由 Scott 完成的 2018年6月6日

Yes that's what it gave me 12V and went down slowly down so the psu is good. I will disassemble the console to see.

由 Róbert Fekete 完成的 2018年6月6日

Hi Robert, I'm having your same problem. Would you be able to tell me what chip did you replace on your motherboard? Thank you.

由 giacomo trezza 完成的 2020年2月14日

Yes I also have the same issue

由 Fosurichard 完成的 2020年12月4日

显示更多的2条评论

添加一条评论

You're 100% sure it's plugged in fully with a good power cord? — TronicsFix
Hi there! Yes I tried with my working ps4's cord and with my ps3 's cord none of them worked. No power at all not with eject button not with power button and also tried to put a Blu ray in to se if that activates the console but nothing. — Róbert Fekete
My PSU is an ADP-200ER (4 pin) not a ADP-240AR like the one in the video. — Róbert Fekete
then you should get the same reading, only it will begin a slow discharged immediately. — Scott
Yes that's what it gave me 12V and went down slowly down so the psu is good. I will disassemble the console to see. — Róbert Fekete
Hi Robert, I'm having your same problem. Would you be able to tell me what chip did you replace on your motherboard? Thank you. — giacomo trezza

PlayStation 4

PS4 CUH-1216D no power after Power Supply Swap

Update (06/23/2018)

1个答案

添加你的答案