跳转到主内容

Black and silver single cup coffee maker with water reservoir on the left hand side. K40/K45.

92 个问题 查看全部

Keurig Elite B40 Won't Close

This morning, my Keurig Elite B40 wouldn't brew. I put in a K-cup, and hit the brew button, but no water came out. So, I proceeded to follow some tips I found online for unclogging the needles and checking the tubes. I had to undo the two screws underneath the top housing, so that I could pull it up and check the tubes. I saw nothing wrong with the tubes, so I replaced the screws without doing anything inside the housing.

Now, the top won't close. When I look inside to see what's blocking it, I see a metal tongue back behind the K-cup holder and a bar that looks like it's supposed to slide over the tongue and into a groove. However, the tongue is completely rigid and locked in place, such that the bar would have no hope of sliding back into the groove. I'm assuming the tongue is supposed to have a little give so that the bar can slide over it into the the groove, but since it's rigid, it's impossible to force the handle closed against that pressure.

I didn't mess with anything in this part of the machine - my fingers wouldn't even fit back there. Did I inadvertently mess something up when I slid the top of the housing off to look at the tubes? Help!

Edit:

I added pictures of the metal tongue and the bar I'm talking about, as well as a photo showing how the Keurig won't close. The photo shows as far down as the handle will go in its current state.

Block Image

Block Image

Block Image

已回答! 显示答案 我也有这个问题

这是一个好问题吗?

得分 12
18条评论

I called Keurig customer service. They said that none of them had ever heard of this issue and it wasn't fixable.

完成的

schmick, post a couple of images with your question. May be we can figure it out if we see what you see. Use 在已经存在的问题里加入图片 this guide to post images

完成的

"However, the tongue is completely rigid and locked in place," just checked mine (working) and it is the same way. So there has to be another reason.

完成的

@oldturkey03 Yeah, I was hoping there was another reason and someone recognized the behavior. Unfortunately even their customer service had no idea.

完成的

@oldturkey03 Even though you already checked and determined that you don't think it's the problem, I added pictures of the metal tongue and the bar I'm talking about. I also added a photo showing how the Keurig won't close. The photo shows as far down as the handle will go in its current state.

完成的

显示更多的13条评论

添加一条评论

10个答案

已选择的解决方案

schmick, here are my pictures, they look pretty much the same. I guess I will have to tear mine apart and check it out. This is not an answer but the only way to post images.

Block Image

Block Image

Block Image

Block Image

这个答案有帮助吗?

得分 3

3条评论:

@oldturkey03 Don't tear yours apart on account of me. I don't want your Keurig broken too!

完成的

I'll get to it right after work. No big deal as long as the wife won't find out:-))

完成的

I believe my problem is similar however I did not remove any screws or do anything to it. Suddenly, you have to hold the lid down with a finger or two to keep it low enough to continue to brew. I guess I will be taking it apart. I was hoping my issue was not unique.

完成的

添加一条评论
最有帮助的答案

We had the same issue. I removed the upper cover, two screws, to find a rouge piece of plastic had kept the mechanism from closing. Couldn't find where it came from. Doesn't seem to prevent it from working. Opens and closes like new.

这个答案有帮助吗?

得分 4

6条评论:

We had the same issue this morning. We turned it up side down to remove the water in preparation for removing the screws, and the cover went down itself. Give this a try before taking it apart.

完成的

I have the same issue after taking apart my Keurig for a thorough cleaning. When I line up the screws for the top cover out won't close. If I shift the cover slightly forward so the screws don't line up, it closes just fine just as it does without the cover on. Any thoughts?

完成的

I did this and it worked .....thank you

完成的

Our lid Quit closing this morning, I found a small piece broke off and I still can"t see where it came from.

I think it was keeping the lid from opening too far. If I pull down slightly on the part inside the lid I can close the lid I'm going to see if my lid has the two plastic sliding pieces on them and snap them off like mj18oneill said they did.

完成的

I have the 2.0 with the same issue. Guess I will be shopping for a new coffee maker. But will turn this in to consumer report. Might need to be a recall.

完成的

显示更多的1条评论

添加一条评论

Unscrew the two screws ( where it says hot liquids), pull back the handle till it closes. Screw in the screws.

这个答案有帮助吗?

得分 3

1条评论:

Hi to add to Kathryn's post, after you have unscrewed the two screws you will be better able to see the sharp metal K-cup puncture tip. The tip more than likely is jammed into the plastic K-cup holder that is removable. Get something strong like the end of a utensil or a screw driver and gently, but forcibly, pry the puncture tip over the top of the K-cup holder. Once you've done so, then put the screws back into place and you're good to go. :)

完成的

添加一条评论

Hi my name is Tina and I have figured it out. OK after the top of your kuerig is off . Look under the top there are 2 long plastic pieces that have a lip on it. Now look down at the inside of the kuerig and you will see 2 holes line up the long plastic piece with the holes . And when they are in push forward. That locks the top in. Now your sews go in with no problem . You now will have no problem closing it. Hope this helped have a great day

这个答案有帮助吗?

得分 3

1条评论:

You are the best. Thank you.

完成的

添加一条评论

I just took a screw driver and snapped off the 2 plastic sliding pieces that have the little arrows on them. There is one on each side. They slide into place when opening and closing the lid. My machine was stuck half way opened and wouldn't shut or move at all. Problem solved. I roughed up the machine, needed coffee! Coffee drinkers don't play!!!

这个答案有帮助吗?

得分 2

3条评论:

That is exactly my problem. My one plastic sliding piece came off at the top and I cannot see enough to put it back in place. I'm not sure where it goes. How did you get yours back on? Do I need to unscrew it for that?

完成的

I had all the same problems I took it apart to really clean it and when I put back the 2 screws to hold the top handle down.... no go so I just put the handle back on with no screws and jiggled it a lot and the doles will eventually line up. Took my about an hour just fiddling . I put on the handle till it fit then turned unit upside down making sure the lid was closed then put the screws back it . It works!

完成的

@librarylady I have the same issue - posted below. Called Keurig - we will see if that helps.

完成的

添加一条评论

Thank you Maureen.

I simply turned the Keurig upsidedown and now it works as new.

这个答案有帮助吗?

得分 2

1条评论:

This worked for me too! See a detailed approach below.

完成的

添加一条评论

The top cover has two plastic hooks about 2/3rds the way back. Those 2 plastic hooks have to

be lined up/hooked it before you put the screws in. A little flashlight helps. You can put the screws in

without putting those 2 hooks in place but it won't work right...and you

might crack the plastic.

这个答案有帮助吗?

得分 2

1条评论:

Keurig Rivo is recently discontinued not because the machine is bad and unrepairable but because Keurig doesn't do service. They did send the new machine as a replacement for repairable one and of course they were losing money.

It happened to me a year ago and now when the same thing happen again, Keurig offer "big" discount if I buy another machine instaed

The Rivo pods wasn't punctured fully, the handle didn't close and the water was pouring out in the pod bean instead into cup.

Any help will be appreciated.

完成的

添加一条评论

Hi had the same problem. Unscrewed the 2 screws and took the top off and when I went to put the top back on and the screw holes wouldn't line up correctly. I messed with it for probably 2 hrs before I tried pushing the back part of the top in more and then held on to it while flipping it over and sure enough that made the screw holes line up correctly.

这个答案有帮助吗?

得分 0
添加一条评论

I had the same issue without having touched the unit. Somewhere a great comment said they had turned the machine upside down to see how to take it apart and when they turned it back the flip top worked once again! Well this worked for me! I also saw where this helped to align the screws holes too - although I never took any screws out from under the "lid" or anywhere. Here is what I did:

1) Take the water tank out/off;

2) Turn it totally upside down (about 1 - 2 ounces of water dripped out - so I did over the sink);

3) I cycled the flip lid back and forth and could hear and feel some rough spots but cycled it 3 or 4 times making sure I went full open then full closed. I could hear that something "clicked";

4) I did not have to push especially hard but after I could tell things had at least been convinced to move and it would close fully (e.g., brew mode) unlike when I started.

When I turned it over it was working again. No more having to hold my finger on the lid to to brew. I hope this works so easily for you!

这个答案有帮助吗?

得分 0
添加一条评论

I have this same issue as some here. Cleaning, and the bracket holding the Pod carrier popped out, and after 3 hours of trying to figure it out - can’t find where it goes back together. You can see the bracket in the picture, and I see in other pictures where it should go.


Anyone have a suggestion on where and how to snap this back in

Block Image

这个答案有帮助吗?

得分 0
添加一条评论

添加你的答案

schmick 将永远感激不已
浏览统计数据:

过去 24 小时: 1

过去 7 天: 4

过去 30 天: 54

总计 25,407