Computer won't turn on after replacing display.

Question

PowerBook G4 Aluminum 15" 1.5-1.67 GHz

Model A1106 / 1280x854 screen resolution

90 个问题查看全部

问题已关闭

Steve @steve47671

声誉积分: 1

1

发帖于: 2010年3月20日

更多选项

Computer won't turn on after replacing display.

I recently purchased a replacement screen for my PowerBook, and followed the instructions on this website. After completing what seemed to be a successful installation, I attempted to reboot the machine, but nothing turns on. I double checked the battery had power, and plugged in the AC adapter as well. I've also gone back and repeated the screen replacement (without actually replacing the new screen), but nothing seems to work. Does anyone know what could cause this problem?

Thanks for any help.

Steve

已回答！ 显示答案我也有这个问题

这是一个好问题吗？

是否

得分 0

添加一条评论

2个答案

已选择的解决方案

lemerise @lemerise

声誉积分: 37.6千

315

66

72

发帖于: 2010年3月20日

更多选项

Double check the trackpad ribbon connection to the logic board. If the connector is not well inserted in the socket there will be no activity when pushing the power button. Reseat the connector in the socket an apply a tape on it to secure the connector to the logic board.

这个答案有帮助吗？

是否

得分 1

5条评论:

Thanks for your response. I've checked that many times, but it doesn't seem to be the issue. Do you know if there's a way to turn the machine on other than the power button? Thanks

由 Steve 完成的 2010年3月20日

Yes, check on the logic board near the trackpad socket (if i remember well) you should see two solder pads and an inscription "Power button" or "PWR". Use a jeweler small flat screwdriver and bridge the two contacts. The PB should start and boot.

由 lemerise 完成的 2010年3月21日

Just tried bridging the solder pads and nothing happened. Is there something I'm not doing right? Or is there any other possible explanation? Thanks again.

由 Steve 完成的 2010年3月22日

Never mind, I was bridging the pads the wrong way. Sure enough, when I bridged them vertically, it started right up! Once that happened, I plugged in the trackpad ribbon to the logic board, and all keys (including trackpad and trackpad button work). The only button that does not work is the power button. How do you suppose I fix this? Thanks for all your help!

由 Steve 完成的 2010年3月22日

Not sure if you can replace the power switch maybe you'll have to buy a used top case without keyboard off ebay and install your keyboard on the "new" top case. Check if there's a way to remove the power switch, I really don't remember if it can be done.

由 lemerise 完成的 2010年3月22日

添加一条评论

Thanks for your response. I've checked that many times, but it doesn't seem to be the issue. Do you know if there's a way to turn the machine on other than the power button? Thanks — Steve
Yes, check on the logic board near the trackpad socket (if i remember well) you should see two solder pads and an inscription "Power button" or "PWR". Use a jeweler small flat screwdriver and bridge the two contacts. The PB should start and boot. — lemerise
Just tried bridging the solder pads and nothing happened. Is there something I'm not doing right? Or is there any other possible explanation? Thanks again. — Steve
Never mind, I was bridging the pads the wrong way. Sure enough, when I bridged them vertically, it started right up! Once that happened, I plugged in the trackpad ribbon to the logic board, and all keys (including trackpad and trackpad button work). The only button that does not work is the power button. How do you suppose I fix this? Thanks for all your help! — Steve
Not sure if you can replace the power switch maybe you'll have to buy a used top case without keyboard off ebay and install your keyboard on the "new" top case. Check if there's a way to remove the power switch, I really don't remember if it can be done. — lemerise

Pierre Brihat @pierrebrih68099 声誉积分: 1 1 1 · Answer 1 · 2011-08-25T10:20:59-07:00

Pierre Brihat @pierrebrih68099

声誉积分: 1

1

发帖于: 2011年8月25日

更多选项

I am having the same problem and i found the two solder pads "Power Button" but what do you mean by bridging them "vertically". I tried to simply bridge them by laying a little screw driver between the two but nothing happens ? Can you explain how you did it ? thanks

Ok found it (as usual, just after posting a message). I was doing it the right way but without the battery present. Plug it in, bridge and … boooinnnng, the welcome boot sound

这个答案有帮助吗？

是否

得分 0

添加一条评论

PowerBook G4 Aluminum 15" 1.5-1.67 GHz

Computer won't turn on after replacing display.

2个答案

Update