跳转到主内容
帮助

当前版本: oldturkey03 ,

文本:

Howard Lowitt, hope everything else is okay after the hurricane. Anyhow, try this first. Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off. If that does not do it, try putting the machine into diagnostic mode.
 
DIAGNOSTIC TEST
 
The washer must be empty and the control must be in the OFF state before pressing the touch-pad sequence to start the test.
 
Starting the Test Mode
 
■ Close the door.
 
■ Push CONTROL/ON (if present on this model).
 
■ Select the DRAIN/SPIN cycle.
 
■ Select NO SPIN by pressing the SPIN SPEED touch-pad.
 
■ Push PREWASH OPTION four times within five seconds. (If PREWASH OPTION is not present on this model, press EXTRA RINSE four times within five seconds.) C:00 will light up on the display.
 
If the Starting procedure fails, push the PAUSE/CANCEL touch-pad, then repeat the starting procedure.
 
Test Program Control
 
In order to advance to the next step of the test procedure, push

PREWASH
PREWASH OPTION touch-pad two times. If PREWASH OPTION is not

present
present on this model, press EXTRA RINSE two times.
In order to advance to the next step of the test procedure, push

PREWASH
PREWASH OPTION touch-pad two times. If PREWASH OPTION is not

present
present on this model, press EXTRA RINSE two times.
 
If that does not work, or if if it won't enter diagnostic mode, then you may need to replace the main control board. You can get the service manual [https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/eab852a13fbc842085256aa200643dd6/|from here]. You can also find plenty of information [http://forum.appliancepartspros.com|on here] and [http://www.managemylife.com/mmh/questions?q=HE3+washer|here as well.] Hope this helps, good luck. Stay safe....

状态:

open

编辑: oldturkey03 ,

文本:

Howard Lowitt, hope everything else is okay after the hurricane. Anyhow, try this first. Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off. If that does not do it, try putting the machine into diagnostic mode.
 
DIAGNOSTIC TEST
 
The washer must be empty and the control must be in the OFF

state
state before pressing the touch-pad sequence to start the test.
The washer must be empty and the control must be in the OFF

state
state before pressing the touch-pad sequence to start the test.
 
Starting the Test Mode
 
■ Close the door.
 
■ Push CONTROL/ON (if present on this model).
 
■ Select the DRAIN/SPIN cycle.
 
■ Select NO SPIN by pressing the SPIN SPEED touch-pad.
 
■ Push PREWASH OPTION four times within five seconds. (If

PREWASH
PREWASH OPTION is not present on this model, press EXTRA RINSE four times within five seconds.) C:00 will light up on the display.
■ Push PREWASH OPTION four times within five seconds. (If

PREWASH
PREWASH OPTION is not present on this model, press EXTRA RINSE four times within five seconds.) C:00 will light up on the display.
 
If the Starting procedure fails, push the PAUSE/CANCEL touch-pad, then repeat the starting procedure.
 
Test Program Control
 
In order to advance to the next step of the test procedure, push
 
PREWASH OPTION touch-pad two times. If PREWASH OPTION is not
 
present on this model, press EXTRA RINSE two times.
 
If that does not work, or if if it won't enter diagnostic mode, then you may need to replace the main control board. You can get the service manual [https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/eab852a13fbc842085256aa200643dd6/|from here]. You can also find plenty of information [http://forum.appliancepartspros.com|on here] and [http://www.managemylife.com/mmh/questions?q=HE3+washer|here as well.] Hope this helps, good luck. Stay safe....

状态:

open

原帖由: oldturkey03 ,

文本:

Howard Lowitt, hope everything else is okay after the hurricane. Anyhow, try this first. Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off. If that does not do it, try putting the machine into diagnostic mode.

DIAGNOSTIC TEST

The washer must be empty and the control must be in the OFF

state before pressing the touch-pad sequence to start the test.

Starting the Test Mode

■ Close the door.

■ Push CONTROL/ON (if present on this model).

■ Select the DRAIN/SPIN cycle.

■ Select NO SPIN by pressing the SPIN SPEED touch-pad.

■ Push PREWASH OPTION four times within five seconds. (If

PREWASH OPTION is not present on this model, press EXTRA RINSE four times within five seconds.) C:00 will light up on the display.

If the Starting procedure fails, push the PAUSE/CANCEL touch-pad, then repeat the starting procedure.

Test Program Control

In order to advance to the next step of the test procedure, push

PREWASH OPTION touch-pad two times. If PREWASH OPTION is not

present on this model, press EXTRA RINSE two times.

If that does not work, or if if it won't enter diagnostic mode, then you may need to replace the main control board. You can get the service manual [https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/eab852a13fbc842085256aa200643dd6/|from here]. You can also find plenty of information [http://forum.appliancepartspros.com|on here] and [http://www.managemylife.com/mmh/questions?q=HE3+washer|here as well.] Hope this helps, good luck. Stay safe....

状态:

open