⟐ Answered 九月 06, 2026 at 22:03 GMT-7

Manufacturer : "ShanWan"
Product : "USB WirelessGamepad "

Device ID : HID\VID_2563&PID_0575\7&17507071&2&0000
Hardware IDs : HID\VID_2563&PID_0575&REV_0200 HID\VID_2563&PID_0575

They were working fine until I transferred my windows from old SSD to new SSD.
When I enter every game I have series of button ( I think they are repeating ) is pressed every 5 to 20 seconds. for example circle back back down start circle even some keys pressed together( up+start+circle).
it is very amazing when I turned the controller off and just dongles attached.
I have tested it on android device and my smart tv and there is no more automatic buttons

⟐ Commented 九月 06, 2026 at 21:55 GMT-7

⟐ Answered 九月 04, 2026 at 0:46 GMT-7

⟐ Answered 九月 03, 2026 at 3:17 GMT-7

⟐ Commented 九月 03, 2026 at 3:12 GMT-7

⟐ Answer accepted 九月 02, 2026 at 20:28 GMT-7

I read on this thread that this issue is caused because of dirt between the contact surfaces of the cable sheet and the trigger and the solution was to just clean them. I've replaced the cable sheet before so I knew how to clean it safely, and so I did, but after I reassembled everything the r2 trigger stopped working all together. The reading in DS4Windows show that the R2 is completely dependent on the left stick now. It doesn't spontaneously activate itself now, but the &&^&^$^ left stick is controlling it.

Here is a demonstration. Can anyone help me out with this? What could be the issue? I found this thread on IFixit which describes the exact problem, but its for the Xbox controller. I don't seem to understand what parts are the DS4 equivalent to be able to narrow down the problem for myself.

⟐ Commented 八月 31, 2026 at 14:08 GMT-7

⟐ Answered 八月 30, 2026 at 22:11 GMT-7

⟐ Answered 八月 28, 2026 at 1:19 GMT-7

All went smooth, my controller works, but L3 is behaving very weird:

It clicks itself when I move the left stick on the left, also when I click it, the click input stays on for more than half a second. This half second is also the same time - more or less - the input lasts when I rotate the stick on the left, here's a video of what happens:

Right stick is flawless.

Calibration went well and all, but I really can't find the cause of this, my soldering was not the best but I've checked multiple times the pins and I don't see any bridge:

I'd really like to avoid desolder and resolder everything, are there some specific pins I should check?

⟐ Answered 八月 28, 2026 at 1:15 GMT-7

next day I wanted to use the controller, it turned off after 1-2 sec, and there could be up to 5 min´s before I could "try" to use it again with the same result. a few times it worked for about 20 sec and I could confirm that the ps5 says the battery on the controller is full, and no charge light comes up when connected to the ps5.

my ps5 at some point got fed up with me trying to reconnect the faulty controller that it wanted to restart and do some kind of repair which took under a sek, and I was not able to read it.

same story with hardware tester usbwired to a pc, it would show up for about a sec. and then disappear. and then randomly show up at different intervals for the same 1 sek.

what would make it do this ?

⟐ Commented 八月 27, 2026 at 2:41 GMT-7

Can anyone recommend a retailer/manufacturer that can sell me replacements for the DPad and the DPad brace? One would think that places selling the DPad would also understand that the brace behind it is likely to break too...

⟐ Commented 八月 25, 2026 at 14:53 GMT-7

The PS button wasn't working so I did a reset with the little button on the back, then it paired. I'm at the user select screen. Analog stick works but d-pad does nothing (not sure if it should do anything here). X and O (only options given for keypresses on that screen) do not work at all. What could I have messed up here?

⟐ Answered 八月 22, 2026 at 19:38 GMT-7

The buttons don't work and my pc won't detect it wired. Even if I connect it wired, it doesn't charge, LED doesn't turn orange. Pressing or holding the power button doesn't do anything, it just keeps blinking blue like in the video above.

Here's some pictures inside, did I mess up somewhere? Any help is appreciated.

Thanks

⟐ Answered 八月 20, 2026 at 0:32 GMT-7

I’m having a problem with a PS5 DualSense controller that stops working when running on battery power. I’ve tried two known-working batteries from another controller, and both work fine in the other controller.

I’ve taken measurements at the battery connector, and it reaches around 4.1–4.2V. I also tried a battery charged to approximately 50%; its voltage increased from around 3.8V to 4.1V, so it appears to be charging correctly.

The controller works perfectly fine when connected via USB cable, but it won’t operate from the battery.

I’ve also tried replacing the DA9087, but nothing has changed.

⟐ Commented 八月 16, 2026 at 13:09 GMT-7

I've been having an issue where the controller will blink white lights whenever it is charging, turned on, or attempts to pair with a device. The controller itself is unusable in this state. I've attempted to fix this by taking out and cleaning the joystick modules, resetting the controller with the button on the back, and directly wiring the controller to a device and resetting it. Nothing has worked so far. Any advice on how to fix this would be greatly appreciated!

⟐ Commented 八月 15, 2026 at 13:35 GMT-7

⟐ Answered 八月 15, 2026 at 9:14 GMT-7

⟐ Commented 八月 13, 2026 at 4:15 GMT-7

⟐ Answered 八月 09, 2026 at 2:21 GMT-7