iFixit - Active Questions With Device "Kitchen Appliance"

Euhomy IM-06D: 电器不工作

Mon, 24 Nov 2025 17:22:09 -0700

制冰机通了电，机器不工作

Pressure Cooker: 为什么我的电压力锅盖不严

Thu, 20 Mar 2025 23:31:21 -0700

电压力锅盖子推上锁后，仍然有缝隙，无法盖严。我想拆开尝试自己维修，但是不知道如何拆解，希望获得帮助，谢谢！

我的电压力锅品牌是松下电器/Panasonic Electric，型号是SR-SG501。

⟐ Answered 三月 20, 2025 at 23:31 GMT-7

Cuisinart DCC-3400: Can not set auto to am. I have tried resetting both auto time and do c

Sat, 16 May 2026 20:24:59 -0700

When setting auto time, it will not show am

⟐ Answered 五月 16, 2026 at 20:24 GMT-7

Cosori Pro II: Could you send more detailed photos

Sat, 16 May 2026 12:11:53 -0700

Could you send more detailed photos of the electronic circuit boards from both sides? Several components on the board are burnt, and I can’t identify them.

Mixer: Kenwood km264 works for 2 seconds then shuts off

Sat, 16 May 2026 07:32:21 -0700

My Kenwood mixer works for 2 seconds on multi speed mode, then turns off. Works for about 5 seconds on pulse mode, then turns off. What could be the issue?

Melitta Coffeemaker: Melitta C35 "Please wait" screen

Thu, 14 May 2026 01:51:31 -0700

Hello everyone,

I am troubleshooting a professional coffee machine (Melitta C35) control board based on the Freescale ColdFire MCF5232CVM100 (BGA package). The system is currently stuck at the initial "Please wait" screen and does not proceed to the main menu.

Hardware Details & Measurements:

· MCU: MCF5232CVM100 (ColdFire V2 Core).

· Flash: cFeon EN29LV160 (TSOP-48).

· Power Rails:

o VDD (Core): Measured 1.6V on the micro-capacitors surrounding the MCF5232.

o VDDIO/Periphery: Stable 3.3V found across the board.

o Analog/Other: 5V rail is present.

· RTC Battery: Measured 3.29V (stable).

· Debug Interfaces: The board provides a standard 26-pin ColdFire BDM header AND a 10-pin (2x5) Mini-BDM connector.

· Service Port: External 9-pin RS-232 (DCE, Female).

Symptoms:

1. On power-up, the display initializes and shows "Please wait".

2. The board has a Reset button that toggles the 3.3V line, but the MCU remains in the same "Please wait" state after reset.

3. I measured -5.6V on the TX pin of the RS-232 port, which indicates that the line driver is powered and the UART is likely initialized by the bootloader.

Questions for the community:

1. Given that the display shows "Please wait", is it safe to assume the MCU has successfully initialized the FlexBus and started executing code from the external Flash?

2. What are the typical reasons for a ColdFire V2 to hang at this stage? Could it be a checksum mismatch in the Flash or a timeout waiting for a peripheral (I2C/SPI)?

3. Does the presence of both 10-pin and 26-pin BDM headers imply any specific debugging priority? Is one more suitable for a USBDM interface to dump the cFeon Flash?

4. Are there any known "trap" states or Double Bus Fault indicators I can check via the BDM pins without a full debugger?

Thank you, Alex

⟐ Answer accepted 五月 14, 2026 at 1:51 GMT-7

Keurig Elite: My Keurig Will not draw water

Tue, 12 May 2026 14:04:50 -0700

My Keurig shows out of water but will not draw water from the reservoir

⟐ Commented 五月 12, 2026 at 14:04 GMT-7

Microwave: Door Latch not Opening Door

Tue, 12 May 2026 08:56:57 -0700

I have a GE Profile microwave that is about 8-1/2 years old. The door latch is not opening the door consistently when I press it. I now have to press it and then with my other hand pull on the top of the door to pull open the door. The microwave is set flush into the kitchen island. Not sure what part(s) I need to order before calling repairman. Model PEB 2060SM1SS, Serial #FR902588U.

⟐ Commented 五月 12, 2026 at 8:56 GMT-7

Melitta Caffeo Solo: Brewing unit won't go back in

Mon, 11 May 2026 09:42:28 -0700

The brewing unit of our Melitta Caffeo Solo did not going back in.

I found mentions of the motor not being properly aligned.

The official FAQ states: The motor might not be in the correct position. Check if the water tank is filled and if the drip tray is in place. Turn the appliance OFF and then ON again. Then simultaneously press the button for My-Coffee and the on/off button for more than 2 seconds. The motor will move into the correct position. Insert the brewing unit again and check that it is correctly locked in position.

However, this proposed solution did not reset the motor position in my case.

I found that the locking handle of the brewing unit moves a metal lever.

This metal lever engages a button in the machine.

By carefully pressing this button (i used the handle of a small spoon), the motor reset to the correct position.

Long story short: I don't have a question, and just wanted to post this here for future reference.

⟐ Commented 五月 11, 2026 at 9:42 GMT-7

Keurig 2.0-400: Keurig 2.0 will not dispense water and make cofee

Mon, 11 May 2026 07:36:49 -0700

it lights up and sounds like its going to dispense water but only a few drops come out

⟐ Commented 五月 11, 2026 at 7:36 GMT-7

Krups F203: Blade and its little base came out of shaft hole. How to get it back i

Sun, 10 May 2026 13:45:33 -0700

Blade and attaching neck came loose in grinding chamber. How to attach it back in so it engages?

⟐ Commented 五月 10, 2026 at 13:45 GMT-7

Breville BOV800XL toaster oven: Fixing the start button

Sat, 09 May 2026 21:52:18 -0700

Pressing the start button on my Breville BOV800XL toaster oven also triggers the convection button, and sometimes the Fahrenheit/Centigrade button, instead of turning on. I have to press the button many times, carefully, before the cycle actually begins.

I suspect the button is flexing the PCB behind the control panel and display.

How do I get the cover off, and how could I fix this?

⟐ Commented 五月 09, 2026 at 21:52 GMT-7

Keurig K-Duo: My Keurig doesn't want to reset after discale

Fri, 08 May 2026 14:29:51 -0700

How can I reset after discale

⟐ Commented 五月 08, 2026 at 14:29 GMT-7

Black and Decker PowerPro II FP1510: Food processor is not working

Fri, 08 May 2026 13:55:10 -0700

I got it as a gift but did not used it for over a year. Now when I want to use it, it does not work. Is there anything that I can look at, repair it myself, find out why it does not work?

Thanks

⟐ Commented 五月 08, 2026 at 13:55 GMT-7

Popcorn Machine: Replacement glass for popcorn machine

Tue, 05 May 2026 11:33:03 -0700

Need a glass window on the popcorn machine replaced

⟐ Commented 五月 05, 2026 at 11:33 GMT-7

SiFENE KC101: Parts - baskets for ground coffee and basket for tea

Tue, 05 May 2026 11:05:48 -0700

Where do I find parts (baskets)

Magic Bullet NutriBullet: Cup stuck to base of NutriBullet

Tue, 05 May 2026 00:08:02 -0700

The cup of the magic NutriBullet is stuck to the base , can’t remove it

⟐ Commented 五月 05, 2026 at 0:08 GMT-7

Ninja Professional Blender 1100 watt: Why is the power light blinking?

Mon, 04 May 2026 17:28:13 -0700

I plugged my blender in and hit the power button, but when I select a speed or press pulse, it wont blend. The red power light just keeps blinking.

⟐ Commented 五月 04, 2026 at 17:28 GMT-7

Keurig Coffee Maker: I made a cup of coffee. Now the lid won't open. It's stuck.

Mon, 04 May 2026 13:44:30 -0700

I made a cup of coffee. Now the lid won't open at all. It's stuck.what should I do?

⟐ Commented 五月 04, 2026 at 13:44 GMT-7

Keurig 2.0-400: How to install replacement keurig 2.0 upper needle gasket 400 series

Sun, 03 May 2026 09:30:23 -0700

Any graphics or illustrations available to show proper installation