⟐ Answered 五月 02, 2026 at 8:22 GMT-7

⟐ Answered 三月 16, 2026 at 4:16 GMT-7

unable to turn printer on

⟐ Answered 七月 24, 2026 at 0:06 GMT-7

⟐ Answered 七月 18, 2026 at 13:12 GMT-7

⟐ Answered 七月 15, 2026 at 4:02 GMT-7

⟐ Answered 七月 13, 2026 at 7:56 GMT-7

⟐ Answered 七月 07, 2026 at 6:28 GMT-7

When I send something to the printer, I can hear the rollers spin and the paper wiggles just a tiny bit (indicating, to me, that there is some contact between the rollers and the paper). There are even "tread marks" on the paper, so that indicates to me that the rollers are trying to grab the paper. But, it just can't seem to "lift" the heavier paper. What I tried was pushing the heavier piece of paper at the start of the print cycle, then the printer was able to grab paper and run it through.

For now, I guess I'll just run cheap, thin paper through the printer. But, I'd like to figure out if there's a way to fix this before I decide to get a new printer.

Patricia

⟐ Commented 七月 06, 2026 at 13:47 GMT-7

I bought the HP OfficeJet Pro 8620 printer in 2015 and up until december 2019 it has worked perfectly. One day out of the blue, I recieved this error message: “The printhead appears to be missing, not detected, or incorrectly installed. Error code 0xc19a0023" . I reseated the printhead one time and the printer worked until next day, when the same error appeared. I followed HP’s troubleshooting steps 1. reset printer 2. reseat printhead 3 times 3. updating firmware, but no luck. I’ve disassembled the printhead and cleaned the contacts on PC board. I ordered this cleaning solution and cleaned the printhead, both soaking in the solution for some time and pushing the solution through. No luck. I then went on to buy this new print head from eBay, but the new one instantly gave the same error message.

Then I continued to troubleshoot some more. Since the new printhead failed I thought maybe the problem is in the printhead carriage inside the printer. I disassembled it and cleaned the contacts on the PC board. (This one is also possible to buy on aliexpress , but I’ve not done it). Everything looks ok. All the pins are undamaged. I’ve reset the CMOS battery on the main board, disconnected all cables and checked the cables specificly for the printhead carriage. I don’t have the equipment or knowledge to test if the cables actually work, but everything looks ok. Still getting the error message.

One last thing that I came by today on this page is that it might be the unoriginal ink that I installed for the first time last time I replaced my cartridges (about 3 months ago, I switched the last color from original HP to unoriginal). Could it really be the problem? Is it still worth a try to buy new original HP cartridges and will it even fix the problem? Or is the damage done already and not reversable? I’m a bit hesitant to invest more on this printer since I already blew up 72 EUR for the printhead…. Returning the printhead to China from where I live costs almost 40 EUR so it’s not worth the refund.

EDIT: I found an official statement from HP about a new firmware update removing Dynamic Security Feature which makes the printer fail when unoriginal ink is installed. However they explicitly say it’s only connected to a cartridge error message. Other error messages are not related. So in theory I’ve already solved this issue, when I updated my printer to the newest firmware early in the troubleshooting process. Both printheads give the same error message. This decreses my belief in buying new original ink to fix the problem…

EDIT 2: I found the old original HP empty cartridges I had before and installed them just to see if it would remove the error, but it didn’t. So now I don’t have to waste money on buying new ink at least…

Or am I missing something else? Thanks for helping out!

⟐ Commented 六月 26, 2026 at 20:53 GMT-7

I am trying to fix a HP Smart Tank 516 printer, but the trace cable is missing in it, if someone knows the length, width and the number of pins you find in the trace cable please let me know.

Thanks

⟐ Commented 六月 20, 2026 at 11:58 GMT-7

​"I am facing an E3 error on my HP Ink Tank Wireless 419 printer. The carriage seems stuck and it’s not printing anything. I have already checked for visible paper jams but the error persists. Could you please guide me on how to fix this carriage jam or if there is an issue with the encoder strip?"

⟐ Answered 六月 20, 2026 at 11:54 GMT-7

I have unplugged the machine, removed the ink carrage and cartriges, does not help.

Any suggestions?

Dave

⟐ Answered 六月 19, 2026 at 1:12 GMT-7

I love this printer and agree with the description you posted. I have extra ink cartridges so would love to fix the printer and keep using until my ink drys up!

⟐ Answered 六月 15, 2026 at 4:28 GMT-7

• Doesn't print in color, despite recognizing the new (3rd Party) toner in it. It can tell how much toner is in each. The printer's built Demo Sheet prints in black and white.
• Trouble printing in general, replaced the two "rolls" in Tray 1. Doesn't 'take' the paper from Tray 2 as well.
• Encounters a 59.C0 error message, fails Color Calibration sometimes. I believe that the solenoid moves freely.

Here's a video of it trying to print: https://www.youtube.com/shorts/lzqZC8-NE...

⟐ Answer edited 六月 14, 2026 at 15:28 GMT-7

⟐ Answered 六月 12, 2026 at 1:35 GMT-7

⟐ Answered 六月 11, 2026 at 8:18 GMT-7